Hakko 927 E S D Manually
Mar 28, 2017 Differential predictors of medication adherence in HIV. 575 Science Dr., Madison, Wl), or by manual alignment and visual inspection (see, e.g. HAKKO KOMBUCHA: MINUMAN TEH. Banjar Kemuning Sedati Sidoarjo 927 Osas Lisa Istifarinta KOLABI 'Kompor Laptop Biomassa' ramah. As recommended in the clinical manual. Mainio A, Hakko H, Niemela A et al.
View and Download HAKO 926 instruction manual online. HAKKO DEVELOPMENT CO., LTD. 4-5 SHIOKUSA 2-CHONE, NANIWAKI OSAKA, 556 JAPAN ROOM 804. Feb 26, 2018 - Hakko 927 E.s.d. Special orders, including all Thermal Imagers, are non-returnable. Defective new equipment may be returned for.
• HAK(O HANKT_ATIOON Please read this instruction manual thoroughly before operating HAKKO 9P+6. • Specification • Station Power Consumption Output Voltage AC24V Temperature 200~480°C/392-896°F Temperature Control Control accuracy of setting at idling temperature.:/-0.5°C (+0.9°F) 125(W) x 120(H) x 200(D) mm Outer Dimensions (without Cord & Holder Part) 4.9(W) x 4.7(H) x 8.1(D) in. Approx 1.5 kg (3.3 lb) Weight (without Cord &.
• Accessories $ Holder Part (consists of: Iron receptacle, Iron Holder Body, Holder Mounting Base, Thumb Screw) • Cleaning Sponge • Tip& Sponge Tray Part Name Handle Cover Temperature Control Knob Handle L.E,D. Heater Lamp Nipple Power Switch Holder Part Holder Body Thumb Screw Cord Asse'y. How to install ppe xcelerator hot. • Precautions Ceramic Heating Element cannot stand excessive force. Never strike Soldering Iron against work-bench or solid surface.
Make sure the Nut securing the Tip Enclosure is properly tightened. Use exclusive Tips for 900 only. Operate in lower tip temperature. Exceptionally high thermal recovery allows.
• Replacement • Caution Temp, compansion with the standard tip. (At 480°C, 896°F) 1 ) Use exclusive tips for HAKKO 900 only. 900M-T-1,6D _.=_ 2 ) The set temperature should be adjusted M-T-2.4O._,_.o%., according to the tip configuration. If required, adjust the temperature. • Trouble Shooting Guide Problem: Turn the power switch on, but Tip does not heat up or over heating.
Condition: The power lamp doesn't light up. CheckPoint: Is the fuse blown? Condition: The fuse is blown.
CheckPoints: 1. • • to check the breakage of Heating Element and Cord Asse'y.
Disconnect the Connecting Plug and measure the resistance value between pins of Connecting Plug as follows Between pin 4 & pin 5 2.5_-3.5 ohm (Heating Element) (Normal) Between pin 1 & pin 2 43_58 (Sensor) (Normal) • Recalibrating of Iron Temperature After replacing the Heating Element or replacing the tip, recalibrate the temperature of the Soldering Iron. 1 ) Connect the Plug of Soldering Iron to the Station and lock it. 2 ) Set Temperature Control Dial at 400'C (752°F). 3 ) Turn the Power Switch. • g Heating Element D-Sleeve 'J' O Nut O Tip Enclosure O Tip O Nipple Grounding Spring Heating Element Glass Tube Heating Element Lead (Red) Sensor Lead (Blue) Terminal Board _ Cord Asse'y _ Handle 1 ) Turn the Nut O counterclockwise and remove the Tip Enclosure. • Replacement Parts Name/Specifications 900M-H Heating Element for 900M Ceramic 24V 50W B1784 Nut for 900M B1786 Tip Enclosure for 900M 900M-044 Nipple for 900M 900M-044S Nipple for 900M (ESD Type) 900M-036 Grounding Spring for 900M 900L-H Heating Element for 900L, Ceramic 24V 50W B1794 Nut for 900L B1787. • CORPOR ION HEAD OFFICE HONG KONG: HAKKO DEVELOPMENT CO., LTD.
4-5 SHIOKUSA 2-CHONE, NANIWAKI OSAKA, 556 JAPAN ROOM 804, EASTERN HARBOUR CENTRE, 28 HOI CHAK STREET, QUARRY SAY, HONG KONG TEL: (06) 561-3225 FAX: (06) 561-8466 TEL: 2811-5588 FAX: 2590-0217 TLX: HAKKOOSA J65274 PHILIPPINES.
We have a Hakko 937 with a '5 - E' error displayed when the unit warms up. Do you know what this means? Thank you, Gary Coulson --------------------------------------- Reply #1 --------------------------------------- When the display indicate S-E it indicates a failure of the sensor or sensor circuit. It could be something as simple as a broken heating element.
Section 14 of the Instruction Manual gives directions for measuring the resistance of the heater and sensor circuits of the heating element. Click this link to download a manual. If the heating element checks out ok you should then 'buss out' the cord assembly to be sure there is not a broken wire, though this would be rare. If neither of these checks determine the cause I would recommend sending the station to our Repair department for evaluation. There is no charge for an estimate. Please call Hakko at 800-88-HAKKO (4-2556) if you would like to send the unit in for service.
You will be given a Return Material Authorization (RMA) number and instructions for sending the unit to us.